Call Us : 9970058287 / 9970058288
ACTUATOR TRAINING SYSTEM is supplied in 4 independent modules with all necessary accessories like Electrical sources (Excluding 230 V AC Mains) , Pneumatic & electrical connectivity, meters & gauges, mounted on pane on M.S. powder coated structure.
MODULE- I ( Electrical Flow actuators) )
A] Solenoid Valve :: ½” ON/OFF type 230 V mains operated.
B] Motorised Control Valve
VALVE : Linear ½ “ Globe valve, SS-316
Stem Travel 18 mm, O/P Thrust 200 Kg Max.
Manual Override Provide with Hand wheel & Clutch.
Class of Protection – IP 55, 2 Nos. of Limit switches
Local position indicator on side Scale
MOTOR : Non blocking AC Sync. 220 V 50 Hz Single Phase
Rating – 4.5 W
POSITIONER : Valve positioned with feedback pot. 100-135 E
ACTUATOR : A.C. servo motor. 230 v/50Hz
CHARA : Linear / equal percentage (optional)
CIRCUITRY : Electronic positioner with 4-20mA. Input & 220 V
AC to Drive Servomotor
INDICATOR : Stem position indicator / flow in direction.
SET-UP : M S structured table top design with Water tank fitted
centrifugal pump, with bypass valve & required fluid
connectivities & Rotameter for flow indication
MODULE- II (Electrical Rotary actuators)
A] DC Servo Motor
2 kg-cm DC Servo motor 12 / 24 V operate with power supply graduated scales on shaft.
B] AC Servo Motor
2 kg-cm DC Servo motor 12 / 24 V operate with power supply graduated scales on shaft.
C] Stepper Motor
MOTOR : Bi-directional permanent magnet bifilar 2 phase D.C. motor
Mounted on M S chassis with calibrated dial & pointer.
MOTOR CHARA. : Self Starting, Low M. I., Instantaneous start, stop & reverse.
TORQUE : 3.5 Kg-cm.
STEPPING ANGLE : 1.8 degree.
PROTECTION : Against Forcible stalling.
Logic indicators for observing logic status of each winding of Motor
POWER SUPPLY : Built in I C regulated
CONNECTOR : Special connector for connecting Motor unit to control unit.
& necessary patch cords are provided.
POWER REQUIRED : 230 V / 50 Hz
D] I-P Converter
Input 4-20 mA Output 3 – 15 PSI
E] Limit Switches
NC & NO type with lever & roller
F] Proxy Inductive
Inductively sensed proxy distance 2-5 mm
G] Proxy Capacitive
Capacitive sensing proxy distance 2-5 mm
H] Proxy Optical
Optically sensed proxy distance 2-5 mm
All the three proxy & limit switches are suitably mounted on panel with sliding object for sensing
MODULE- III
Module III consist of four valves suitably mounted on M.S. structure with necessary C-PVC heat resistance, non corrosive piping, all the three are connected in parallel with series ON-OFF manual valve for selecting desired valve in operation. Pneumatic ON-OFF valve is provided in series with main fluid line to demonstrate ON-OFF action. I-P converter & FRL unit is also include on this panel so as to demonstrate practical working of I-P converter coupled with Valve.
A] Pneumatic ON/OFF Valve
B] Pneumatic Linear Valve
C] Pneumatic Quick Open Valve
D] Pneumatic Equal % valve
VALVE DETAILS : Linear, Equal % & Quick open valves :
(Can choose any one or all the three as per requirement)
VALVE TYPE : Globe type
LINE SIZE : 15 mm
VALVE LIFT : 28 mm
INLET Pr. : 4 Kg.
DIFF. Pr. : 4 Kg Max.
CONTROL Pr. : 3 – 15 PSI
ACTUATION : Diaphragm Reverse actuated
Close on supply failure
PNEUMATIC : ¼” N.P.T.
CONNECTION
BODY : CS SS-316
BONET TYPE :Standard Vertical Mount
E] I-P Converter Input 4-20 mA Output 3 – 15 PSI
F] Fluid set up for above Sump. Submersible float pump, manual bypass valve & fluid circulation system
MODULE- VI
A] Pneumatic Single Acting Cylinder 100mm strock x 25 mm piston
B] Pneumatic Double Acting Cylinder 100mm strock x 25 mm piston
with Magnetic sensing
C] Pneumatic DC valve 3 x 2 Direction control Valve
D] Pneumatic Multidirectional Valve 5 x 2 Multidirectional control valve
E] Pneumatic Rotary Actuator 90 degree On-OFF Rotary
F] Pneumatic Manifold 5 Port manifold
G] Compressor 90 PSI